How do I login to my hitron router?

Login Instructions

  1. In the address bar, type in the following: 192.168. 0.1 and press the enter key on your keyboard.
  2. You will be presented with a Hitron login page.
  3. Login with your credentials: Hitron CGNM-2250. Username: cusadmin.
  4. Select the Login button.

What is the default login for hitron router?

Hitron router login normally has a default username “cusadmin“, and the default password “password“. Its default IP address is 192.168. 0.1. These Hitron credentials are needed when doing a login to the Hitron router’s web interface to change any settings.

What is the default Cusadmin password?

The default username is cusadmin, and the default password is highspeed or CantTouchThis. To improve the security of your router, we recommend changing the default admin password. Launch a web browser like Firefox or Chrome from a connected wired or WiFi device. Type in the IP address to access the login page.

How do I find the password for my hitron router?

Hitron CGN2

  1. Connect your device to your Wi-Fi modem:
  2. Open a web browser and key in 192.168.0.1 in the address bar and press Enter.
  3. Enter the following default settings to access the modem settings and select Login:
  4. Select the Wireless menu option from the left side of the page.
  5. Select the Security tab.

Why can’t I log into my hitron router?

Re: Unable to login to Hitron CGN2-ROG modem You could try a hard reset on the device (hold the reset in for a good 10+ seconds). Or you can call into tech support, they should be able to log in via their login into the device, and reset the password for you.

How do I reset my hitron router username and password?

Enter the current password (case sensitive) found on the white sticker on your modem. Click Wireless at the top of the page. Click 2.4G, 5G, or Guest network at the top of the page, to select a network to change the password for. Under Multiple SSID Setting, type a new network password in the Pass phrase field.

How do I reset my hitron admin password?

Restore default password

  1. Locate the small pin-hole reset button on the back of your Shaw modem.
  2. Push and hold the button with a paperclip or pin and hold for 15 seconds.
  3. The lights on the modem will begin to flash if the reset was successful.

How do I reset my hitron WIFI password?

Changing the wireless network password

  1. Enter 192.168.
  2. Log in with the following information:
  3. From the home page, select Manage Wireless.
  4. Select the 2.4G, 5G, or Guest network from the top of the page.
  5. Under the Multiple SSID Settings, next to Passphrase, enter a new network password.
  6. Save your changes.

Where is the reset button on hitron modem?

Using the modem’s Reset button:

  1. Locate the Reset button on the back of the modem.
  2. Press and hold the Reset button for 10 seconds.
  3. After 10 seconds, release the button. The modem should restart and the lights will flash.
  4. Once the modem is finished restarting and is online the settings will be back to default.

How to enter your Hitron Technologies username and password?

This means that in order to login to them you start with your web browser. Enter Your Hitron Technologies Router IP Address Into your web browser’s Address Bar Enter your Hitron Technologies Router username and password when prompted The list of user names and passwords is below.

What is the default username and password for HITRON cgnm-2250?

To login with the modem Hitron CGNM-2250 you will need to use the following default username and password: cusadmin/Printed on Router Label Others IP addresses used by the router brand Hitron

What should I know about MSO log on?

The information contained herein is provided as a courtesy and is for general informational purposes only. It is not intended to be a complete description of all applicable policies and procedures. The matters referenced herein are subject to change without notice.

What’s the difference between SSID and username in HITRON?

SSID: I was hoping to create a “replacement” wireless network from my old one that was running on DD-WRT in a TP-Link router. My SSID included “2.4” to distinguish it from the “5.0” that I was hoping to add! There were other letters ahead of the “2.4” (the quotes were not part of it). Hitron does not seem to like the “.”

By Uncategorized