## How many amps should a well pump draw?

A 240 volt, 1 horsepower well pump draws 10 amps of current. When the pump starts, it can draw up to 35 amps, but only for 5–10 seconds.

How many amps does a 1.5 HP water pump use?

A 230v 1.5 HP submersible pump is metering about 11.4 amps per leg.

How many gallons per minute does a 1/2 HP well pump?

A two-line jet pump can typically raise water from depths of 30-feet to 80-feet, and at water delivery rates of 4 gpm (gallons per minute) (for a 1/2 hp 2-line jet pump serving an 80 foot deep well) to 16 gpm (for a 1 hp 2-line jet pump serving a 30 foot deep well).

### What size breaker do I need for a 1 HP well pump?

Answer: Almost all the motors require 220-volt motors. So, the horsepower of the pump is the factor. For example, ½ HP pump needs a 15 amp breaker. But the ideal circuit breaker will be 25 amps for a 1 HP pump.

What size breaker do I need for a 3/4 HP well pump?

Registered. Most of the well pumps i have wired are around 7 amps at 240. I think that is the rating of a 3/4 hp. Most well guys here run 10 G for everything an assume it needs to be on a 30 amp breaker.

How many amps does a 1 HP pool pump draw?

1 HP is 746 watts x 1.5 HP = 1,119 watts. 1,119watts ÷ 120volts= 9.325 amps.

## How many amps is a 3 HP well pump?

Your pump must be smaller than 1/2 HP for a 4.3 amps @230 volt nameplate….How many watts does a 1 HP well pump use?

Household & Office Running Wattage Starting Wattage
Pump, Well, 1 HP 2000 4000
Pump, Well, 1 – 1/2 HP 2500 5000
Pump, Well, 2 HP 3750 7500
Pump, Well, 3 HP 5000 10000

What size wire do I run to my well pump?

Conductor Sizes About the largest pump cable you will ever see in water well applications is 500 MCM. We are talking heavy cable — more than five pounds per foot for three conductors. If you are doing residential work, most of the pump cable you use will be in the #6 to #14 AWG range.

Are all well pumps 220?

As mentioned earlier, it is important to consider the type of power your well pump equipment requires. Most residential pumping equipment is single phase 230 volts, however, some small pumps in the USA may use 120 volts single phase. Larger pumping installations may require 208, 230 volt or 480 volt 3-phase power.

### How many amps does a 1/3 HP pool pump draw?

1 HP submersible pump motor will draw a current of 3. 2 amperes if it is single phase motor at a voltage of 230 volts, and if it is a 3phase motor at a voltage of 440 volts, it will draw a current of 1.7 amperes, maximum….How many amps does a 1 HP 3 phase motor draw?

HP 110-120 Volts
1.5 20 10

How many Watts Does a well pump use?

Consumer reports says a well pump runs about 700 watts. Multiply that by 3 to get a rough estimate of the starting wattage for the pump and you run about 2100 which still leaves plenty of wiggle room in terms of wattage.

What size breaker for a well pump?

Re: Breaker recommendation for 1hp well pump. NEC standards are intended to protect the wire, not the pump. Since you have 10 gauge wire, by NEC you can use a 30A breaker or smaller, since 10 gauge copper wire can carry 30A.

## What is a well pump used for?

A water well pump is a device used to draw water up from a well for delivery to a home or other structure. Pumps are necessary in sunk wells because the water cannot rise to the surface on its own.

What is a shallow well pump?

As initially stated, the shallow well jet pump is a pump that works well on wells or reservoirs that have a total pumping depth of 25 feet or less. These pumps are made up of three components: an electric motor, a jet assembly, and an impeller.